Configuration InstructionsEdition 12/09BP-PR PLUS & BBP72 SeriesPerforation CutterEdition 04/10Operator’s ManualY1147484
Printer ConfigurationTechnical Data 6 Edition 0410 PERFORATION CUTTER OPERATOR’S MANUAL1. For setting the cutter parameters select:Setup > Machine
PERFORATION CUTTER OPERATOR’S MANUAL 7 Edition 04/10Printer ConfigurationTechnical Data 2. Select the method for recognizing the material and the meth
Loading MaterialTechnical Data 8 Edition 0410 PERFORATION CUTTER OPERATOR’S MANUAL4 Loading Material• Load transfer ribbon and endless material as des
PERFORATION CUTTER OPERATOR’S MANUAL 9 Edition 04/10OperationTechnical Data 4. For direct programming use the following command :O Cn n...Value betwee
MaintenanceCleaning10 Edition 0410 PERFORATION CUTTER OPERATOR’S MANUAL6 Maintenance6-1 CleaningWARNINGDisconnect the printer from the electrical outl
PERFORATION CUTTER OPERATOR’S MANUAL 11 Edition 04/10MaintenanceCleaning3. Remove dust and paper particles with a soft brush or a vacuum.4. For cleani
MaintenanceChanging the Blades12 Edition 0410 PERFORATION CUTTER OPERATOR’S MANUAL6-2 Changing the BladesWARNINGDisconnect the printer from the electr
PERFORATION CUTTER OPERATOR’S MANUAL 13 Edition 04/10MaintenanceChanging the Blades5. Loosen the screws [8] and remove the bearing plate [15]. The spr
MaintenanceChanging the Blades14 Edition 0410 PERFORATION CUTTER OPERATOR’S MANUAL16. Hang in the slack spring [13] to the pins [12,14] of the lineal
PERFORATION CUTTER OPERATOR’S MANUAL 15 Edition 04/10MaintenanceSetting Initial State of the Cutter6-3 Setting Initial State of the CutterTo operate t
ii Edition 04/10 PERFORATION CUTTER OPERATOR’S MANUALInformation on the scope of delivery, appearance, performance, dimensions and weight reflect our
MaintenanceSetting Initial State of the Cutter16 Edition 0410 PERFORATION CUTTER OPERATOR’S MANUAL4. Check the position of the clock wheel [11].• If t
PERFORATION CUTTER OPERATOR’S MANUAL 17 Edition 04/10ComplianceUNITED STATES & CANADA 7 Compliance7‐1UNITEDSTATES&CANADAFCC Class A Noti
ComplianceEU Conformity Declaration18 Edition 0410 PERFORATION CUTTER OPERATOR’S MANUAL7-2 EU Conformity DeclarationWe declare herewith that as a resu
PERFORATION CUTTER OPERATOR’S MANUAL iii Edition 04/10Approval The transfer printers comply with the following safety guidelines: Batteries Directive
iv Edition 04/10 PERFORATION CUTTER OPERATOR’S MANUALContents1 Introduction...
PERFORATION CUTTER OPERATOR’S MANUAL 1 Edition 04/101 Introduction1-1 Intended UseThe device is intended exclusively as an option for the printers of
IntroductionSafety Instructions2 Edition 0410 PERFORATION CUTTER OPERATOR’S MANUAL1-2 Safety Instructions• Disconnect the printer from the electrical
PERFORATION CUTTER OPERATOR’S MANUAL 3 Edition 04/10IntroductionTechnical Data 1-3 Environment 1-4 Technical Data Note: To operate the Perforation Cut
MountingTechnical Data 4 Edition 0410 PERFORATION CUTTER OPERATOR’S MANUAL2 MountingNote: Disconnect the printer from the electrical outlet before mou
PERFORATION CUTTER OPERATOR’S MANUAL 5 Edition 04/10Printer ConfigurationTechnical Data 3 Printer ConfigurationOnce the cutter is connected to the pri
Comments to this Manuals