Brady Wraptor User's Guide Page 67
- Page / 72
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
5. Using a 7/64” Allen wrench, remove the screw that is located above the printhead assembly stamping.
Save the screw for installation of the new assembly.
Printhead mountin
g
pivot shaft—washer
and screw are located
on the opposite side.
Screw—located
above the
p
rinthead
assembly
6. Using a 5/32” Allen wrench, remove the washer and screw located opposite the printhead mounting
pivot shaft. You will need to reach around to the back of the printer to remove the washer and screw.
Save the washer and screw for installation of the new assembly.
7. Remove the printhead assembly. Make sure that the printhead ribbon cable is eased part way through
the cable slot.
8. Remove the strain relief tape (if present) from the printhead ribbon cable.
9. Disconnect the printhead ribbon cable from the printhead assembly, noting the orientation of the cable.
NOTE: It is important to note the orientation of the
printhead ribbon cable when disconnecting it as you will
need to connect it the same way.
To install the new printhead assembly:
1. Connect the printhead ribbon cable to the printhead assembly, orientating it the same way as it was
when removed. (See Step 9 above.)
2. Replace strain relief tape if it was present on the printhead ribbon cable at the time it was disconnected.
(See Step 8 above.)
3. Install the printhead assembly, ensuring that the printhead ribbon cable and connector are eased back
through the cable slot.
4. Using a 5/32” Allen wrench, replace the washer and screw located opposite the printhead mounting
pivot shaft.
5. Using a 7/64” Allen wrench, replace the screw that is located above the printhead assembly stamping.
6. Replace label material and ribbon, and close the side door.
60 Wraptor™ User’s Guide
- User’s Guide 1
- Copyright 2
- Regulatory Information 3
- Brady Warranty 3
- Wraptor™ User’s Guide III 4
- Table of Contents 5
- Table of Figures 7
- Chapter 1 Introduction 8
- 1.4 Technical Specifications 9
- Wraptor™ User’s Guide 3 10
- Chapter 2 Safety 11
- 2.2 Electrical Safety 12
- 2.3 Warning Labels 12
- 3.1 External Parts 13
- Wraptor™ User’s Guide 7 14
- 4.1 Initial Setup 15
- 10 Wraptor™ User’s Guide 17
- Wraptor™ User’s Guide 11 18
- 12 Wraptor™ User’s Guide 19
- Wraptor™ User’s Guide 13 20
- IP Address Option 21
- 14 Wraptor™ User’s Guide 21
- Printer Name Option 22
- Wraptor™ User’s Guide 15 22
- 16 Wraptor™ User’s Guide 23
- 4.2 Load Label Material 24
- 18 Wraptor™ User’s Guide 25
- Wraptor™ User’s Guide 19 26
- 20 Wraptor™ User’s Guide 27
- Wraptor™ User’s Guide 21 28
- 22 Wraptor™ User’s Guide 29
- 4.3 Load the Printer Ribbon 30
- 24 Wraptor™ User’s Guide 31
- Wraptor™ User’s Guide 25 32
- 26 Wraptor™ User’s Guide 33
- Adjustment for Wire Bundles 34
- Wraptor™ User’s Guide 27 34
- 5.2 Using the Touch Screen 35
- Figure 12. File Tab Menu 36
- Wraptor™ User’s Guide 29 36
- Open Command 37
- 30 Wraptor™ User’s Guide 37
- 5.3.2 Run Tab Commands 38
- Figure 15. Goto… Dialog 39
- 32 Wraptor™ User’s Guide 39
- Figure 16. Setup Tab Menu 40
- Wraptor™ User’s Guide 33 40
- Figure 17. Adj Tab Menu 41
- 34 Wraptor™ User’s Guide 41
- Advanced Settings Menu 42
- Advanced Settings Commands 42
- Wraptor™ User’s Guide 35 42
- Figure 20. Config Tab Menu 43
- Connection Type 43
- Operating Modes 43
- 36 Wraptor™ User’s Guide 43
- File Location 44
- Remote Control 44
- Figure 21. IP Tab Menu 44
- Wraptor™ User’s Guide 37 44
- Entering Text 45
- 38 Wraptor™ User’s Guide 45
- Description of Settings 46
- Wraptor™ User’s Guide 39 46
- 40 Wraptor™ User’s Guide 47
- Wraptor™ User’s Guide 41 48
- 42 Wraptor™ User’s Guide 49
- 5.5 Power Off 50
- 44 Wraptor™ User’s Guide 51
- Wraptor™ User’s Guide 45 52
- 46 Wraptor™ User’s Guide 53
- Wraptor™ User’s Guide 47 54
- 48 Wraptor™ User’s Guide 55
- Wraptor™ User’s Guide 49 56
- Chapter 7 Maintenance 57
- Wraptor™ User’s Guide 51 58
- Figure 33. Clean Printhead 59
- 52 Wraptor™ User’s Guide 59
- Figure 34. Clean Rollers 60
- Wraptor™ User’s Guide 53 60
- Figure 35. Clean V-Rollers 61
- 54 Wraptor™ User’s Guide 61
- Wraptor™ User’s Guide 55 62
- 6. Close the unit doors 63
- 7.2 Lubrication 64
- 58 Wraptor™ User’s Guide 65
- Wraptor™ User’s Guide 59 66
- 60 Wraptor™ User’s Guide 67
- Chapter 8 Error Messages 68
- 62 Wraptor™ User’s Guide 69
- Wraptor™ User’s Guide 63 70
- 64 Wraptor™ User’s Guide 71
- 9.1 Consumable material 72
- 9.2 Accessories 72
Related products and manuals for Label printers Brady Wraptor
Label printers Brady LabelMark 3 User Manual
(84 pages)
(84 pages)
Label printers Brady 203X-PLUS User's Guide
(110 pages)
(110 pages)
Label printers Brady 200M-e 300 Specifications
(118 pages)
(118 pages)
Label printers Brady 1024 User's Guide
(55 pages)
(55 pages)
Label printers Brady 2024 User's Guide
(89 pages)
(89 pages)
Label printers Brady 260M User's Guide
(104 pages)
(104 pages)
Label printers Brady POWERMark Specifications
(128 pages)
(128 pages)
Label printers Brady Handi User Manual
(1 pages)
(1 pages)
Label printers Brady 1024 Operator's Manual
(82 pages)
(82 pages)
© 2020, manymanuals.com. All rights reserved. | 2.119 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals